Information
Can I leave the filter pump/sand filter outside while it's raining?
Close Me
Yes, you can. But we suggest to not use the pump when it is thundering or lightning.
Can I use my Flowclear filter pump with bigger models of pools, and what should I do?
Close Me
First you have to check if the flow rate of your pump is suitable with the water quantity of the new pool, and then you have to make sure the hose connections are compatible.
Can the filter pump be used when a cover is on the pool?
Close Me
Yes. There is no problem in using the pump when the pool is covered.
Can the Sand Filter with Ozonator work without the Ozon function?
Close Me
Yes, the sand filter can work without the Ozonator. You have to place the timer on position 0.
Can we use the pool while the filtration system is operating?
Close Me
No, please do not use the swimming pool when the filtration system is operating.
How can I set the correct operation time of my Flowclear Sand Filter with Ozonator?
Close Me
Consult the Owner’s Manual section for the operating time table with Ozonator.
How do I find the suitable length of hoses for my pool size?
Close Me
For pools smaller than 22 ft. (6.71 m), reduce the number of long hoses simultaneously until the total length is equivalent to the length from dedicated suction line to the fastest point in the pool.
How does the sand filter work?
Close Me
The water from the pool flows through the strainer, up through the control valve, down through the sand, up through the collector hub in the center and out through the control valve back to the pool. Dirt and debris from the pool water are trapped in the sand and clean water is returned into the pool.
How does the timer on the Sand Filter work?
Close Me
The timer on the sand filter has 9 different positions. Each position has different cycle. You can leave the sand filter connected to the power source, and the sand filter will operate automatically following the cycle you set:
Position 4: working time 4 hours / waiting time 20 hours
Position 6: Working time 6 hours / waiting time 18 hours
Position 8: Working time 8 hours / waiting time 16 hours
Position 10: Working time 10 hours / waiting time 14 hours
Position 12: Working time 12 hours / witing time 12 hours
Position 24: Working time 24 hours
the below three positions are the automatic cycle, and it means that if you set one of these positions, the sand filter will continuously operate following the cycle.
Position P4: Cycle working time 4 hours / waiting time 4 hours
Position P6: Cycle working time 6 hours / waiting time 6 hours
Position P8: Cycle working time 8 hours / waiting time 8 hours
How many years will the pool last?
Close Me
There is no set time limit for the pools to last. Following the instructions in the owner’s manual and with proper care, maintenance and storage, you can considerably increase the life of your pool. Improper set-up, storage and usage can instead reduce it drastically.
How much weight does a ladder support?
Close Me
Bestway has two weight standards for the ladders: 145 kg (331 lbs) and 305 kg (672 lbs), depending on the safety standards of the country. Bestway ladders are in compliance with all international and national safety standards.
Is it necessary to use a filter pump with my Skimatic filter pump?
Close Me
No, it is not necessary to use an additional filtration system if you installed the Flowclear Skimatic on the pool also. this filtration system has two functions integrated into one item:Skimmer Filter Pump
Is it possible to use a timer with my filter pump?
Close Me
IMPORTANT: the timer cannot be used if the filter pump is equipped with an external RCD or GFCI. The timer will compromize the functionality of the products. If the filter pump doesn't have an external PRCD or GFCI, you can use the timer. If you installed the filter pump together with a chlorinator or a pool heater, be sure the chlorinator has already finished the set cycle or switch off the pool heater before the filter pump.
Is it possible to use a timer with my sand filter?
Close Me
The timer cannot be used if the sand filter is equipped with an external RCD or GFCI. The timer will compromize the functionality of the products. If the sand filter doesn't have an external PRCD or GFCI, you can use the timer.
If you installed the sand filter together with a chlorinator or a pool heater, be sure the chlorinator has already finished the set cycle or switch off the pool heater before the sand filter.
Is it safe to jump or dive into the pool from the ladder or any type of platform?
Close Me
No. Under no circumstances should you jump or dive into the pool. Bestway does not sell any pools that are deep enough for such activities, and failure to abide by this rule may likely result in serious injury, paralysis or death.
Is the Skimatic filter pump suitable for all Bestway pools?
Close Me
The Bestway Flowclear Skimatic filter pump is suitable with all dimensions of frames of Bestway pools and with the inflatable ring of the Fast Set pool, thanks to the two sets of hooks included in the product set.
IMPORTANT: the only structure in the Bestway pool range that is not compatible with the Skimatic Filter Pump is the steel wall Pool.
IMPORTANT: when you buy this product, be sure that the flow rate of the Skimatic filter pump is compatible with the water quantity in your pool. See the enclosed table for your reference.
The ladder is not completely stable when a person begins to climb it. Is this normal?
Close Me
Yes. This is absolutely normal because the ladder must be flexible enough to adapt to the weight pressure of the person mounting it.
What are the functions performed by the sand filter?
Close Me
Bestway Flowclear sand filters have 6 functions:
1. Filter: This function is used to filter pool water and should be positioned here 99% of the time. Water is pumped through the sand filter, where it is cleaned and returned to the pool.
2. Backwash: This function is used to clean the sand bed. Water is pumped down through the collector hub, upwards through the sand bed, and deposited out of Port D.
3. Rinse: This function is for initial startup, cleaning, and sand bed leveling after backwash. Water is pumped downwards through the sand bed, up through the collector hub and deposited out of Port D.
4. Drain: This function drains water from the pool. Another filter bypass setting, water is pumped and deposited out of Port D, instead of returning to the pool.
5. Circulate: This function circulates pool water bypassing the sand filter. Use this function if the filter is broken to collect debris in the debris screens.
6. Closed: This function stops water flowing between the sand filter and the pool.
What causes my guarantee to break?
Close Me
The legal warranty doesn’t cover damages due to actions not assignable to the seller/manufacturer, to improper or not normal use of the product by the consumer, or to actions contrary to warnings or instructions written in the user’s manual.
What is the correct pump size for my pool?
Close Me
To define the correct size of filtration system for Bestway's Above Ground Pools, you need to know the water capacity of your pool. You can find this information on the package and in the owner manual.
What is the most important function of my filter pump?
Close Me
The most important function of a filter pump is the elimination of every sort of impurity from the water with the aid of a filter cartridge and chemical products for its sterilization.
Where can I find Bestway instruction videos?
Close Me
You can find instruction videos on www.bestwaycorp.com in the support section, or on the Bestway YouTube channel.
Where can I find Bestway User Manuals?
Close Me
You can find Bestway User Manuals on www.bestwaycorp.com in the support section.
Where can I find the capacity in L/hour or gal/hour for my filter pump?
Close Me
On the packaging, you can find the capacity in cbm/hour of your filter pump.
Where do I find the Serial Number?
Close Me
All Bestway products have their own serial number, and they are located in different positions and have different formats. Please see the guide at the following link: https://www.bestway.eu/it-it/#serial-number-overlay or the video below.
Where I can find the dimensions of my Bestway pool and its maximum water capacity?
Close Me
You can find the dimensions and maximum water capacity of your product on the packaging.
Where may I purchase the replacement for filter cartridges?
Close Me
The filter cartridges are available from your local pool supplier or in our Bestway Store
Why is the sand flowing into the pool?
Close Me
1. The sand is too thin and can pass through the skimmer. Please make sure that you are using the recommended size of sand: 0.45 mm to 0.85 mm.
2. The quality of the sand is not suitable to be used with the filtration system of the swimming pool.
3. The skimmer is damaged.
4. The rinsing was not long enough after the backwash. Please consult the owner's manual to perform the correct operations.
Why is there condensation inside the pressure gauge?
Close Me
To read the working pressure of the sand filter, the water goes through the pressure gauge. The condensation is created on the external surface of the pressure gauge due to the difference between the temperature of the water in the pool and the external temperature. Thanks to the high quality of the pressure gauge, the condensation doesn't influence the normal operation of the sand filter.
Maintenance
Can the filter cartridge be cleaned in the dishwasher?
Close Me
The filter cartridge can be cleaned in the dishwasher using temperatures under 30 ℃ and without using any detergent or degreasing.
For safety reasons, since the dirty filter cartridge contains bacteria and other harmful substances, any other dish or kitchen item should not be washed together with the dirty cartridge. Be sure to sanitize the dishwasher before starting the normal operations.
Can the filter cartridge be rinsed out?
Close Me
The filter cartridge can be rinsed out with a garden hose and reused. However, if the filter cartridge remains soiled and discolored, then the filter cartridge should be replaced.
Do I need to disassemble my pool for the winter?
Close Me
It is strongly recommended to disassemble the pool for the winter. The above ground pools may collapse under the weight of ice and snow, which would greatly damage the PVC pool walls. We recommend disassembling the pool when temperatures fall below 10ºC / 50ºF.
Do you recommend using pool chemicals?
Close Me
Yes, we recommend using pool chemicals to maintain the proper chemical levels of the water. Pool chemicals can also make maintenance easier by significantly reducing the amount of times you change your water during the season. Important: always follow the safety instructions written on the chemical products.
How can I connect the pool cleaner to a pool equipped with a Flowclear Skimatic Pump?
Close Me
IMPORTANT: the adaptor necessary to connect the Flowclear Skimatic Pump may not be included in the set. If you need to connect the Skimatic Pump to the pool cleaner, ask your pool dealer to purchase the compatible adaptor.
To connect the pool cleaner to the Flowclear Skimatic Pump follow these instructions:
1. Unplug the pump
2. Unscrew the top ring to take out the strainer
3. Insert the adaptor inside the case of the skimmer on the hole in the bottom
4. Connect the hose of the pool cleaner to the adaptor
5. Plug in the pump to start to operate the pool cleaner
For more information check the attached video.
How do I change the filter cartridge on a Filter Pump that is connected to a pool with 3 connections (A-B-B), without a connection valve?
Close Me
1. Put the stopper plug inside the pool to close the valves. 2. Remove the filter cap and replace the old filter cartridge with the new one.
3. Close the filter cap and take out the stopper plug from inside the pool.
4. Before starting the filter pump, open the purge valve to purge all residual air inside the filter pump.
How do I change the filter cartridge?
Close Me
To change the filter cartridge, follow the below steps:
1. Switch off and unplug the pump
2. Put the stopper plug inside the pool to close the valves. If the pool is equipped with connection valves, close them.
3. Remove the filter cap and replace the old filter cartridge with the new one.
4. Close the filter cap and take out the stopper plug from inside the pool.
5. Before starting the filter pump, open the purge valve to purge all residual air inside the filter pump.
How do I clean the filter cartridge in Bestway's Flowclear filter pump?
Close Me
First step is that you have to put the stopper plug inside the pool to close the valves. If the pool is equipped with connection valves, close them.
Second step: take out the filter cartridge from the filter housing.
Third Step: rinse out with a garden hose and reuse. However, if the filter cartridge remains soiled and discolored, then it should be replaced.
Fourth step: close the filter cap and take out the stopper plug from inside the pool.
Fifth step: before starting the filter pump, open the purge valve to purge all residual air inside the filter pump.
For more information, please see below technical video and file.
How do I maintain the filter cartridge in my Skimatic filter pump?
Close Me
IMPORTANT: Please ensure the skimmer’s motor is unplugged before any maintenance begins.
To perform the maintenance of the filter cartridge in Skimatic filter pump follow the below steps:
1. Unplug the pump.
2. Unscrew the top ring to take out the strainer and remove any debris.
3. Remove the pump from the pool.
4. Unscrew the cap using a crosshead screwdriver (not included) and remove the filter cartridge.
5. Rinse with water. If the filter cartridge remains soiled and discolored, you should replace it with a new one.
How do I use talcum powder on pool frames?
Close Me
Apply the powder on the top rail sleeve, and let it evenly distribute.
How long should I run my filter pump every day?
Close Me
We recommend to run the filter pump/sand filter minimum 8 hours every day; this is the necessary time to circulate the entire pool water.
The increase of the operating hours depends on the quality of the water or how often the pool is used.
How many times a year should I change the water?
Close Me
This depends on the frequency of use of the pool. If performing a correct chemical maintenance, the water should last a full summer season. Please contact your local pool chemical supplier for detailed information regarding chemical maintenance; they will be able to properly advise you about maintaining the cleanliness of your water.
How often I should perform Backwash and Rinse in Bestway Flowclear Sand Filter?
Close Me
Bestway's Flowclear sand filter is equipped with a pressure gauge that shows the working pressure. If it reaches the red level, it means that the sand is full of debris, and the backwash function must be performed for 5 minutes. After that, rinse for 2 minutes. Important: backwash and rinse functions reduce the quantity of water in your pool, so remember to refill the water to have the correct level of water inside the pool.
How often must the air be purged out from the filter pump?
Close Me
The purge air operation on the Flowclear filter pump has to be performed before the first start or after all maintenace operation of the pumps.
How often should I change the sand in my filter?
Close Me
Under normal operating conditions, sand should be changed in residential filters every 4 to 5 years. In areas with high air contaminants such as dust, leaves or any condition that requires frequent backwashing, the sand may need to be changed every 2 to 3 years.
How often should the filter cartridge be replaced?
Close Me
To ensure your pool water keeps clean, please check the filter cartridge one time a week, if required.
In any case we recommend to change the filter cartridge every 2 weeks, depending on usage.
However, if the filter cartridge remains soiled and discolored, the filter cartridge should be replaced.
How to fold the pool liner?
Close Me
Watch the video for detailed information.
I tried to change the filter cartridge and my pool emptied, what should I do?
Close Me
We invite you to follow the instructions on the owner’s manual provided with the filter pump. Please kindly note that it is necessary to accomplish an important operation in order to replace the filter cartridge without emptying the pool. Before removing the filter cap, put the blue plug in the pool valves to avoid water flowing out.
Is it possible to maintain clean pool water using only the filter pump?
Close Me
No, the filter pump can help to capture the particles suspended in the water, but to keep water clean, it is necessary to use chemical products to maintain the correct chemical balance of the water.
The reading on Pressure Gauge is higher than the recommended pressure, what can I do?
Close Me
If the pressure reading on the pressure gauge is over the maximum pressure mentioned in the user manual, it could be the time to clean the sand. Before cleaning the sand, check the following:
- If there is anything blocking the hoses
- If the connection valves are closed or partially closed
- If there is any hole on the hoses
- Turn off the sand filter and check if the pressure goes to 0
After having checked the above conditions, please follow the instructions on the manual to perform backwash and rinsing. If there is still a high-pressure reading, sand bed replacement is necessary.
What can I do if the free chlorine level is over 4ppm after test with the Bestway® Strip Test?
Close Me
If the chlorine level is too high, don’t use the pool until the chlorine level drops below 4ppm.
To decrease the chlorine level follow the instructions below:
1. Unplug the chlorinator and then the filter pump/sand filter.
2. Drain approximately 20% of the water from your pool.
3. Refill until it reaches the correct level.
4. Run the filter pump/sand filter for 8 hours.
5. Test the chlorine level again with the Bestway test strips.
6. Repeat step 2 until the level of chlorine is between 2ppm and 4ppm.
What can I do if the pool water is still dirty after using the pump?
Close Me
To create the correct maintenace procedures for your water, follow these instructions:
1. Increase filtration time.
2. Check the filter cartridge every day and rinse with water. If the filter cartridge remains soiled and discolored, you should replace it with a new one.
3. The filter pump is not able to eliminate all bacterica in the water. The most important part to keeping the water clean is keeping the correct chemical balance in the water. Check with your checmical dealer to get the correct quantity and type of chemical to have the correct water maintenace.
What can I do if white flakes appear in the water?
Close Me
The presence of white flakes in your water depends on the hardness of the water. Drain about 20 to 25% of the pool water and add fresh water to decrease the calcium hardness. Visually inspect the electrolytic cell for scale buildup and clean the electrolytic cell if necessary.
If the above operation doesn't solve the problem, contact your nearest chemical supplier to purchase the correct chemical to reduce the hardness of the water.
What is the correct chemistry condition?
Close Me
Free Chlorine: 2.0 - 4.0ppm
Combined Chlorine <4ppm
pH 7.4 - 7.6
Total Alkalinity 80 - 120ppm
Calcium Hardness 250 - 500ppm
Stabilizer (Cyanuric Acid) 30 -50ppm
What is the correct way to change the sand in Bestway's Flowclear Sand Filter?
Close Me
Please follow these steps to replace the sand:
First step: switch off the sand filter and unplug the socket from the power outlet. Second step: put the stopper inside the pool to close the valve. If the pool has connection valves, close them.
Third step: disconnect the hoses that connect the sand filter to the pool. This will make it easier to remove the sand. Fourth step: open the drain valve on the bottom of the sand filter to drain all residual water into the sand filter body. To speed up the operation, position the control valve between two functions.
Fifth step: open the metal ring in the middle of the tank body and open the upper part of the tank. Sixth step: take out all old sand from the tank and rinse the bottom part with a garden hose to be sure it is clean.
Seventh step: fill the bottom part with the new sand until it reaches the mark between low and high marked on the hub.
IMPORTANT: cover the hole on the top of the hub to avoid the sand going inside, and add the sand gently to avoid damaging the debris screen at the bottom of the tank.
Eighth step: position the top part back in place, and tighten the metal ring to close the tank.
IMPORTANT: when performing this operation, please be sure that the O-ring is in the correct position and completely clean from the sand.
Ninth step: close the drain valve cap on the bottom part of the sand filter.
Tenth step: position the control valve in the backwash position and connect the sand filter to the pool.
IMPORTANT: every time you change the sand in the sand filter, before using with the pool, you must perform the backwash function for 5 minutes and the rinse function for 2 minutes. This important operation will clean the new sand and stop dirty sand from flowing into the pool on the first use.
What should I do if I notice debris and dirt on the floor of my pool?
Close Me
In there is debris or dirt on the floor of the pool, we recommend using the Bestway Deluxe Maintenance Kit or choosing from our wide variety of Bestway cleaning accessories. Using the correct accessories to maintain your pool can increase the life of your water.
What should I do if my water turns green?
Close Me
If the water becomes green due to the incorrect chemical maintenance, establish the correct chemical balance by contacting your local chemical dealer. They will suggest the correct products to use and the frequency.
Why is the water turning white?
Close Me
If the water becomes white, it is the chemical reaction between the chemical used and the quality of the water. Consult your chemical dealer to adjust the water condition.
Why isn't water flowing between the pump and the pool?
Close Me
If there is no flow between the pump and the pool follow these steps:
1. Be sure that the socket has power and the switch on the pump is in the on position. Put your hand on the pump to feel the vibration of the motor.
2. See if there is anything that blocking the hoses.
3. Check if the control valve is positioned on the filter function.
4. Perform the backwash and rinse functions. Open the cap on the Port D and be sure that water flows out with power.
5. If all of the above operations function and the problem still remains, it is the time to replace the sand.
